Light Seal Placement Guides

Minolta XD Placement Guide

Minolta XD Placement Guide | XD | XD-5 | XD-7 | XD-11 Light Seals

USCamera Light Seals | Kits | Foam Sheets | Minolta Film Cameras
Minolta XD Placement Guide | XD | XD-5 | XD-7 | XD-11 Light Seals

Before doing anything, please read about seal removal and installation.

This Minolta XD light seal kit is always in stock.

We add new parts, light seals, and downloads are added almost every day.

Please contact us with any questions or requests you may have.

Tech Note: Most camera body channel seals are installed starting at the hinge end, working towards the latch side until the seal is used up

You are installing an 5-piece kit for the Minolta XD series of film cameras.

Minolta XD Placement Guide

See all light seal placement guides currently available.

Back Cover

Bottom channel seal, back cover, hinge end – 1 x 1mm
Top channel seal, back cover, hinge end – 1 x 1mm
Hinge seal, back cover  – 1 x 2mm

Camera Body

Bottom channel seal, camera body – 1 x 2mm
Top channel seal, camera body – 2  x 1.5mm*
*you will need to cut a small piece from this channel seal, to fit the top channel, starting at the hinge end to the counter lever opening. That piece should measure close to 25mm.

 

Minolta XD Placement Guide

Minolta XD Placement Guide | XD | XD-5 | XD-7 | XD-11 Light Seals

In addition, see all USCamera Light seal kits available for Minolta film cameras.

First of all, the most important and time-consuming work is removing the old seals. Focus on clean, clean, clean. Also, pay careful attention and clean all old residue from the door channels, mirror cushion area, door hinge area and anywhere else you are replacing the seals.

You need to understand the finest adhesive in the world will not adhere to that sticky, gooey residue that was once a quality light seal. Finally, an accurate installation will give you thousands of light tight exposures.

USCamera | Premium Quality Open Cell Foam Lasts Years | Same Japanese Foam As Original | Minolta XD Placement Guide USCamera Light Seals

Lastly, Mamiya cameras are now Mamiya Leaf or Phase One …. their website is not secure. Hum… look here.

author-avatar

About Gray

As a 1979 graduate of National Camera's resident camera repair school, is where I found what I best at and wanted to do for the rest of my working career. After camera repair school, I found my gift was the ability to easily understand complex electro-mechanical photo products. I could take almost any imaging item apart, cameras, lenses, slide/movie projectors plus more, understand how the unit functioned, and repair it. Then, accurately reassemble it into a fully working unit. In 1980, I was employed in Denver as a technician for the largest Colorado camera service center performing repair and service of both in and out of warranty for over 38 brands of photographic equipment, accumulating over 5000 hours of bench time. In 1983, I started Technik Camera as a self-employed contractor and general technician. Within a few years, I employed 4 more technicians, 2 people as support staff, and more. I accumulated another 40,000 hours of bench time as we serviced 110mm, 35mm, medium format film cameras, lenses, flash, enlargers, timers, paper processors, long roll portrait cameras, and more. The challenge of successfully taking anything photographic apart and reassembling it into an accurately working piece... and you could not tell I took it apart, was very satisfying for me. Before 1998, we attended many training seminars hosted by factory trainers from Canon, Fuji, Konica, Mamiya, Minolta, Nikon, Olympus, Pentax, and more. Except for a few products, I have worked on most equipment made and thoroughly enjoyed it. When digital products came to market, I didn’t find the digital service as satisfying as film equipment. So I took the time to develop a website that supported digital/film cameras, lenses, other imaging items with parts and service information. I continued to service my equipment and several customers who maintained large collections. The challenge of successfully taking anything photographic apart and reassembling it into an accurately working piece... and you could not tell I took it apart, was enough for me. I have attended many training seminars hosted by factory trainers from Canon, Fuji, Mamiya, Minolta, Nikon, Olympus, Pentax, and Ricoh. I have special tools and test jigs required for many repairs for Canon, Pentax, Rollei, Rolleiflex, and more. I do not work on studio flash. I don't care much for Alpha, Bronica S2 S2a, some Contaflex, and Kodak leaf shutter reflex mirror cameras plus a few others. I enjoy working on almost everything related to film, though in the last few years my focus is on equipment that will not require parts I don’t have. I am adding to the product service list on the service page. I could not include everything I work on there. Sometimes customers will ask if I can fix their model and I am surprised it wasn’t listed. I was working on photo products long before websites were here and I have not needed to advertise for years. I have plenty of my cameras to maintain as well as many local camera collectors with large collections. So do not hesitate to contact me with a service question about your equipment. I am sure I can take care of any issue you may have with the maintenance or service required with your film cameras, lenses, and more. I was working on photo products long before websites were here and I have not needed to advertise for years. Kindest regards, Gray.

Back to list

Leave a Reply

Your email address will not be published. Required fields are marked *